Author Archive

September 16, 2014

MongoDB + AEM Production Servers


I response to my previous post, here is the basics of a sharded cluster MongoDB setup. As you can see, if you were to place each element on its own server you’d end up with alot of servers.

Sharded Mongo

After a bit of research into how each mongo element is used and its performance characteristics, I arrived at the following sleek(er) configuration of servers. This is arrangement is symmetric to allow for cross data center architectures.



This post was heavily influenced by a concise Will Burton post:

12:48 PM Comments (0) Permalink
July 22, 2014

AEM6 + Mongo Minimal Setup

With the release of AEM 6.0, clustering has been rethought in the form of Apache Jackrabbit “Oak” and the introduction to the concept of microkernels. The initial microkernel that supports clustering uses MongoDB (v. 2.6+) for persistence. This post will provide a real working example of a minimal authoring cluster using a fault-tolerant MongoDB microkernel.

If I receive enough demand, I can also post a production quality MongoDB setup.

What you’ll need:

  • MongoDB installed
  • AEM 6.0 quickstart jar
  • Oracle JRE 1.7

The examples provided were tested using an OS X host but should be compatible on Windows as well as other Unix hosts.

Prep Work

  1. Install the MongoDB binaries
    (I used homebrew: sudo brew install mongodb)
  2. Install the Oracle JDK/JRE v 1.7 (if you haven’t already)
  3. Create a directory for housing your mongo data. I used “aem6_cluster”.
  4. Inside that directory, create these directories: node0,node1,arb0
    The two node directories will be the data directories for two members of a replica set. The arb directory is the data directory for an arbiter.
  5. From the main cluster directory, create another folder named “author”.
  6. Copy your aem 6 quickstart jar and license file to that directory. (Rename the quickstart to this if needed: aem6-author-p4502.jar)

MongoDB Logo

MongoDB setup

  1. From the main cluster directory run this mongo command (from terminal or command prompt):
     mongod --dbpath node0/ --replSet aem6
  2. Enter the mongo util in another terminal window:
  3. Initialize the replica set named in step 7:
     rs.initiate(rsconf = {_id: "aem6", members: [{_id: 0, host: "<hostname>:27017"}]})
  4. After the command is issued, it should return a json response with “ok”: 1. Keep this terminal window open.
  5. From the main cluster directory run this mongo command (from a new terminal or command prompt):
     mongod --dbpath node1/ --replSet aem6 --port 27018
  6. Back in the mongo util window that we kept open, issue this command to add the new node to the replica set:
  7. Once again, if the command executes correctly you should get a json response with “ok” : 1. Keep this window open (again).
  8. From the main cluster directory run this mongo command (from a new terminal or command prompt):
     mongod --port 27019 --dbpath arb0 --replSet aem6
  9. Back in the mongo util window that we kept open, issue this command to add this new node as an arbiter:

At this point we have a clean mongo replica set with 3 members. There should be a PRIMARY and SECONDARY with an aribter node to break up any ties for voting who is the PRIMARY. The two nodes provide minimal redundancy. If one goes down, the other takes over. If both go down, you’re up a creek.

AEM Logo

AEM 6 startup

From the author directory, issue this command:

 java -XX:MaxPermSize=512M -mx4g -jar aem6-author-p4502.jar -r crx3,crx3mongo -Doak.mongo.uri=mongodb://<hostname>:27017,<hostname>:27018

AEM should install and replicate automatically to the mongo nodes. Installation on pretty quick SSD-based mac takes less that 5 minutes (results may vary).

You can now repeat this process on any number of AEM instances as long as they are running on separate ports. Each AEM instance will be active+active in the cluster.

Note the run modes: crx,crx3mongo. The JVM settings can be left out – I just like to dedicate a bit more RAM.

Mongo Notes

To test out the fault tolerance, just ctl+c the mongo instance and watch the AEM driver switch to the elected PRIMARY.

Mongo replica sets must have an odd number of members. An arbiter is not required, but it allows you to have nicely divisible replica sets.

1:00 PM Permalink